Building A Mega Surfcasting Rod for Heavier Weights – Initial Testing

This Mega Surfcasting Rod is Designed for Casting Heavy Sinkers

Part 1 – Surfcasting Rod Initial Testing 

The author at Birdlings Flat, near Christchurch, about to make the first few tentative casts with the Kilwell 9 oz blank. The guides on the surfcasting rod are all held in place with insulation tape just to try it out. Part 2 – Assembly and Fishing Video

All fishing rods, surfcasting rods especially, are designed and built as a compromise between many factors. Among these being lightness; casting ability; fish fighting ability; toughness; the reel to be used, and cost.

The most important attribute for a surfcasting rod is, in my view, it’s qualities as a casting instrument. I regard this factor as first and foremost in my thinking, with the other considerations a distant second. The greater the ability of a rod for making very long distance casts, the more I like it.

I have long wanted to build a really powerful surf rod. One that would toss a heavy sinker and baited hooks far out towards the horizon. A heavier sinker is essential when sea conditions are rough, with a heavy swell and, or, sideways rip. However one of the biggest hurdles has been to secure a good quality surf rod blank that is sufficiently stiff in the butt section to enable up to 9 oz to be cast without the danger of the rod snapping. I also prefer a surf rod to be good and long, somewhere between 15 and 16 feet.

Rod building is less popular today than it was in the past. There is a much greater range of rods available in stores today. However, if you are looking for a specialised rod, such as a big, powerful, extra long surfcasting rod, then building it yourself is still a good option. I also built this rod “turning jig” which is essential for a professional finish. I have a small electric motor which connects to the end of the jig to keep the rod slowly revolving, which is the secret to obtaining a perfect glass-like finish to the epoxy coated line guides. The jig extends off to the right of the picture and can be adjusted for different length rods. It also makes it much easier to do a good job of the line guide bindings. 

After some research, I was able to take delivery of a real “beast” of a surf rod blank. The 13′ two-piece graphite surf rod blank, that had arrived by special order from Kilwell Sports in Rotorua, was everything I had hoped for. I had never seen anything remotely like it before. My most powerful surf rod was an Australian made Titan Series Snyder/Glas S 153 8 Wrap designed to cast up to 180 gms (about 6.5 oz).

Big sevengill shark caught surfcasting at night with the Southern Mega Surf Beast rod.

This thing that had arrived from Kilwell Sports made the Titan feel like a “wet noodle” in comparison. The Kilwell graphite rod blank is simply called a 9oz blank. It is apparently was not sold in New Zealand. Instead only being sold for export, mostly to the Hawaiian Islands. The huge ocean surf in that part of the world being, presumably, the conditions the rod is most suited for.

Before we go any further I’d like to point out that the main purpose of such a powerful surf rod to enable the angler to continue to fish in what would otherwise be marginal conditions. To get out over the crashing breakers, and to keep your line in place in a heavy swell requires a good deal of sinker weight. Somewhere in the region of 8 or 9 ounces is sometimes necessary to prevent your sinker from being washed around onto the beach. To cast this sort of weight you need a very strong rod with good length.

I must admit to being a little awe-struck and uncertain as to what it would be like to cast with. After all the tip section looked to have very thick walls, and be beefier than the average 24 kg ocean trolling rod!

The butt section appeared to have about as much bend in it as a 7-foot section of concrete telegraph pole! The weight also was a bit of a surprise. It meant that the finished rod was going to weigh in around 3 lbs or 1.6 kg. This is before you add on the weight of your reel, sinker and bait! I could see, that if nothing else, it was going to take a bit of muscle to operate effectively. Just how it would perform as a casting tool was the subject of some conjecture and discussion. There was only one way to find out how it would perform: tape on a set of guides and head down to the beach.

Subscribe to Fishingmag
Get the latest fishing articles, news, videos, tips, and updates. The Fishingmag newsletter is delivered to your inbox every Friday.
Here you can see the Mega Surfcasting Rod in action at Kaikoura. Note there is only a little curve in the lower half of the rod.  Surfcasting with such a long powerful rod takes a lot more effort on the part of the angler both when casting and retrieving. Its main advantages are the ability to cast heavy sinkers well out over the surf that hold in place on the bottom even in a heavy swell.

Initial Testing of the Surfcasting Rod Blank Setup

I wanted this surfcasting rod to be at least 15 feet long so decided the way to go was to extend the butt with the addition of a length of aluminium tube. For testing purposes I used some odd lengths of old fibreglass surf rod pushed together to create the necessary extra couple of feet.

I taped the line guides in place with insulation tape. I also secured the extension with plastic tape to prevent it from coming apart while doing a test. Finally, I glued the tip in place with Araldite.

On arrival at the Birdlings Flat, I assembled the rod, and connected my Alvey 650c reel, tied on a 170g (6 oz) sinker, and approached the first cast with some trepidation. To my surprise, the rod worked extremely well and cast the sinker as far as I have ever cast this weight before. A couple of dozen casts later and I was sold on Killwell’s 9oz graphite blank. This thing really works.

One of the Fuji BNHG three-foot aluminium oxide line guides used in the project.

A word of warning about the weight; for anyone contemplating building their own. This is a heavy outfit to fish with. It takes a reasonable amount of strength to operate. This minor drawback is much less of a problem when surfcasting because most of your time is spent with the rod in your beach spike. The beauty of it is that extremely long casts are possible with heavy surfcasting sinkers; more with a lobbing action than with a flick as you might with a lighter setup.

My verdict: all things considered, if you want a top of the line distance casting surf rod and don’t mind the extra weight, you won’t find a better rod than this. However, it is important to note that this huge rod isn’t what I would describe as an “every day” surf rod. Even if you were to build the rod for use with a large fixed spool reel (egg-beater) it would still be a very heavy outfit that would require a lot of extra effort when casting and retrieving. In calm conditions, this sort of heavy firepower just isn’t necessary.

You can see the finished Mega Surfcasting Rod at the beginning of this video below.

Continued in part 2 – Putting the Mega Surfcasting Rod Together

This post was last modified on 13/01/2019 7:26 pm

Leave a Comment
Published by

Recent Posts

Wairarapa Trout – Kopouranga, Waipoua and Mangatarere Streams

Waiarapa Trout Fishing by Catherine Morrison "These were lake trout, which upon release all headed…


White Shark – Carcharodon carcharias – Fishing Methods

Great White Sharks by Allan Burgess Also known as White Shark, White Death, Man Eater,…


The Best Salmon Fishing Rivers New Zealand Map – 27 waters in all

The Best Salmon Fishing Rivers in New Zealand The best salmon fishing rivers New Zealand…


FG knot, How to Tie it and Why you should be using it when Spin Fishing

FG knot and why you should be using it when fishing the Twizel Canals  By…


School Shark Tagging Program Awareness – How You Can Help – Updated

School Shark Tag Awareness - How You Can Help Scroll down for 28 August 2021…


Trout Bait Fishing Secrets – Confessions of a Bait Angler

By Piscator Not without a certain amount of soul searching, liberally mixed with fear and…